Cleaning skateboard bearings is an important part of maintaining your board and keeping it running smoothly. Skateboard bearings are small but vital parts that allow the wheels to spin freely. Dirty or worn-out bearings can significantly reduce the performance of a board, making it difficult to control and reducing speed.

Fortunately, cleaning these tiny components is fairly simple and straightforward if you have the necessary supplies. All you need is some bearing cleaner, mineral spirits (optional), a toothbrush or rag for scrubbing, cotton swabs/Q-tips for getting into tight places, and paper towels to dry off afterwards. With these items in hand, you’ll be able to keep your skateboard running like new in no time!

  • Step 1: Remove the Wheels: First, use a skate tool or Phillips head screwdriver to unscrew and remove all four wheels from your skateboard
  • Step 2: Take Apart the Bearings: Then carefully take apart each bearing by removing its rubber shield on one side and then using a flathead screwdriver to pry it off of the wheel axle
  • Step 3: Clean Out Dust and Debris: Once you have taken apart your bearings, use an old toothbrush or cotton swab dipped in rubbing alcohol to clean out any dust, dirt, and debris that has built up inside of them. Make sure to get into all of their crevices for thorough cleaning
  • Step 4: Dry Off Excess Liquid : Finally, use a cloth or paper towel to dry off any excess liquid from the cleaning process so that your bearings do not rust when they are put back together

How to Clean Skateboard Bearings | Tactics

What Can I Use to Clean My Skateboard Bearings?

It’s no secret that skateboarding requires a lot of maintenance. Skateboard bearings are arguably the most important component to take care of since they are responsible for providing speed and allowing you to turn or maneuver your board with ease. Bearing maintenance is an often overlooked part of skateboarding, but it can have a big impact on how your board performs.

So, what can you use to clean your skateboard bearings? One option is to use WD-40 specialist degreaser spray. This product is designed specifically for cleaning off grime and dirt from metal surfaces such as skateboard bearings.

Simply spray some onto the bearing surface, allow it to sit for a few minutes before scrubbing away any remaining debris with a brush or cloth. It’s also important not to oversaturate the bearing as this could cause damage over time due to corrosion if left uncleaned too long.

Another option would be white spirit cleaner which is commonly used by mechanics when working on cars and other machinery that has been exposed to heavy grease or oil-based substances like those found in some skate parks or ramps where riders often go riding.

White spirit cleaner works similarly as WD-40, just apply it directly onto the bearing surfaces then let sit for 10 minutes before wiping away excess residue with either a rag or paper towel depending on how much gunk there may be stuck on them beforehand!

Finally, if all else fails you can always try using acetone nail polish remover – this should help remove stubborn stains and dirt without causing harm (in moderate amounts). Just make sure not to let any acetone accumulate inside the bearing itself otherwise this could lead potential wear down sooner than expected so always wipe away any excess once finished cleaning up!

Overall, keeping your skateboard bearings clean will help keep them running smoothly throughout their lifespan while giving you better performance overall – from both turning ability & speed perspective alike!

Is It Worth It to Clean Skateboard Bearings?

If you’re a skater, then you know that skateboard bearings are essential for smooth riding. Without them, your board would be nearly impossible to ride. But even though they’re important, many people don’t take the time to clean their bearings regularly—or at all!

Is it worth it to clean skateboard bearings? Absolutely! Here’s why:

Cleaning your skateboard bearings can help them last longer and perform better. Over time, dirt and debris can accumulate on your bearing’s surfaces which can cause friction and make it harder for your wheels to spin freely. This not only reduces the speed of your board but also puts extra strain on the motor which could result in an early breakdown or malfunctioning parts.

By cleaning off these contaminants with some rubbing alcohol or mineral oil every few weeks (depending on how often you use them), you’ll keep them running smoothly and extend their lifespan considerably. Additionally, having clean skateboard bearings will enhance performance by increasing speed and improving maneuverability while skating. The less dirt that is present between the moving parts of the bearing, the easier it will be for them to spin quickly when pressure is applied from pushing off the ground or turning corners sharply.

As a result, riders will experience smoother rides with more control both during tricks as well as cruising around town without any hiccups along the way due to dirty components slowing down progress or making unexpected stops altogether! In conclusion, taking just a few minutes out of each month (or week if necessary) to properly care for one’s skateboard bearings is definitely worth it in order receive maximum enjoyment from their board in terms of improved performance and extended longevity — so don’t forget about this crucial step next time before hitting up those ramps again!

What Liquid Can I Use to Clean My Bearings?

When it comes to cleaning your bearings, there are many different liquids that can be used. Depending on the condition of your bearings, one liquid may work better than another. In this blog post, we’ll explore some of the most common liquids used for bearing cleaning and how to use them effectively.

One of the most popular liquids used for bearing cleaning is WD-40 Multi-Use Product. This product contains a lubricant which helps clean and protect moving parts from rust and corrosion while also providing moisture protection. To use WD-40 Multi-Use Product as a bearing cleaner, spray liberally onto a clean cloth and wipe down each individual bearing until all dirt or debris has been removed from its surface.

You can then take a dry cloth or paper towel to remove any excess product before reassembling your bearings back into place. Another popular liquid for cleaning bearings is rubbing alcohol (also known as Isopropyl Alcohol). Rubbing alcohol evaporates quickly so when using it to clean bearings ensure you apply enough pressure so the excess does not run off onto other surfaces in order to avoid damage caused by evaporation burns.

Simply apply rubbing alcohol directly onto each individual bearing using either a cotton swab or lint free cloth until all visible dirt has been removed before wiping away with a dry cloth or paper towel afterwards.

If you have more heavily corroded balls within your bearings then you might want to consider soaking them in mineral oil overnight instead of attempting immediate removal with just liquids alone; this will help break up any built up grime without damaging any delicate parts within the ball-bearing itself during removal process.

Simply submerge entire assembly into container filled with sufficient amount of mineral oil and leave overnight allowing time for gunk / residue buildup dissolve away naturally over course of several hours before rinsing off gently with warm water afterwards prior final drying stage by hand/air dyer depending on type material being worked upon (e.g.; steel vs plastic etc.).

Finally, if none of these methods work then it may be necessary to disassemble each individual ball from its housing in order to thoroughly remove all traces of dirt/grime build up – once done carefully reassemble components back together ensuring no extra force applied during tightening process otherwise risk damaging fragile internal structure leading premature failure later down line!

Can I Use Wd40 to Clean Skateboard Bearings?

If you’re an avid skateboarder, you know how important it is to keep your bearings clean and well-maintained. But can WD40 be used as part of this routine? The answer is both yes and no.

WD40 is a light lubricant that works great at loosening up rust and other debris on metal surfaces. This makes it ideal for cleaning skateboard bearings, which are typically made from steel or stainless steel. However, WD40 should not be used as a substitute for proper bearing maintenance – instead it should only be used in cases where the bearings have become heavily rusted or soiled with dirt or grime.

To use WD40 to clean your skateboard bearings, start by removing them from the board and placing them in a container filled with warm water and detergent (or vinegar). Allow the parts to soak for about 30 minutes before wiping off any excess dirt with a rag or brush. Once the parts are dry, spray some WD40 onto them then wipe away any remaining residue using another cloth or paper towel until all components look shiny again.

If necessary, repeat these steps until they appear completely free of rust/soil build-up. Once finished, reassemble your board’s bearing assembly per manufacturer’s instructions (usually including applying fresh grease) prior to riding again! Doing so will help ensure maximum performance while protecting against further wear & tear due to lack of lubrication over time – something that can happen when relying solely on WD40 alone long term!

Overall, while WD 40 is an effective tool when it comes to cleaning rusty/dirty skateboard bearings every now and then; regular bearing maintenance through degreasing/greasing remains essential if you want your setup running smoothly day after day without fail!

How to Clean Skateboard Bearings


How to Clean Skateboard Wheels And Bearings

If you’re a skateboarder, you know that keeping your board in good shape is essential for a smooth ride. A crucial part of any skateboard is the wheels and bearings – they are what allow your board to move forward quickly and smoothly. Unfortunately, over time these two components can become dirty, which can affect their performance.

That’s why it’s important to regularly clean them to keep them running at their best. Here’s how to do it: 1. Start by removing the wheels from your skateboard using an Allen key or screwdriver (depending on how they were installed).

Place the wheels into a bowl of warm water and add some dish soap – this will help loosen any dirt or grime that has accumulated on them over time. Let soak for 5-10 minutes before taking each wheel out one by one and scrubbing with an old toothbrush. This will help further remove any stubborn dirt or debris from the surface of each wheel as well as in between its spokes if necessary.

Rinse off each wheel thoroughly once finished scrubbing then set aside for later use when reassembling the skateboard after cleaning its bearings too! 2. Next up are those pesky little bearings! Before doing anything else make sure there is no grease residue left behind on either side of where these pieces fit onto your axle rods; if so wipe down with rubbing alcohol first until all traces are gone before proceeding further with cleaning process!

Once complete take apart each bearing separately using needle nose pliers to carefully pull apart its inner rings while simultaneously pushing outwards on outer metal casing – this should reveal small steel balls inside which can then be removed easily enough too (just be careful not & lose track of original order!). Then place all components into another bowl filled with warm soapy water again like done previously with wheels themselves but instead also adding 1-2 drops liquid dish detergent specifically designed for delicate items such as bearings  (this helps break down build-up without damaging surfaces) – let sit 15-20 minutes before rinsing everything off very well afterwards setting aside dry completely before reassembly begins once more! 3 .

Finally put it all back together again starting from inserting steel balls first followed closely by inner rings & finally outer casings lastly securing both sides firmly onto axle rods once more – don’t forget about lubricating lightly afterward so parts don’t rub against one another causing premature wear !

How to Clean Skateboard Bearings With Household Items

If you’re a skateboarder, then you know that having clean skateboard bearings is essential for smooth rides. But over time, dirt and grime can accumulate in the bearings, leading to poor performance. Luckily, it’s easy to clean your skateboard bearings with some household items — no fancy tools required!

Here’s how: 1) Remove the Wheels – The first step is to remove all four wheels from your board. It’s easiest if you use a bearing puller or just pop them off with a flat head screwdriver — but if you don’t have either of these tools on hand, a pair of pliers will work just fine too!

2) Clean Out the Bearings – Once your wheels are off, take out each bearing and set it aside on a paper towel. Then grab an old toothbrush (or any other kind of soft brush), dip it into some warm soapy water and gently scrub away any dirt or debris from the inside and outside of each bearing. If there are any particularly stubborn bits stuck in there, try using rubbing alcohol as well for extra cleaning power.

3) Rinse & Dry – When you’ve finished brushing away all the dirt particles from each bearing, rinse them under warm running water until they look completely clean again. Finally, lay out another paper towel and place the now-clean bearings onto it; pat them dry with another piece of cloth or paper towel before moving onto step 4! 4) Lubricate & Reassemble Bearings – Before putting everything back together again grab some light machine oil (or even cooking oil!) and apply 1–2 drops to each cleaned bearing before inserting them back into their wheel slots once more.

Make sure they spin freely after doing this; if they feel tight at all give them one final drop of lube before tightening down those screws securely! And that’s it — simple as that!

How to Clean Skateboard Bearings Without Removing Them

If you’re an avid skateboarder, you know that cleaning your skateboard bearings is essential to keeping them in good condition and ensuring smooth rides. But did you know that it’s possible to clean your bearings without removing them from the board? Cleaning your skateboard bearings without removing them can save time and hassle, so read on for a step-by-step guide on how to do just that!

1. Start by gathering all the supplies you’ll need: rubbing alcohol, cotton swabs or q-tips, a small bowl of water (preferably warm), and rags or paper towels.

2. Place one bearing at a time onto a rag or paper towel and use the rubbing alcohol to wipe away any dirt or grime from its surface. If there are any tough spots, use a q-tip with some more rubbing alcohol applied directly onto it for better scrubbing power.

3. Once each bearing has been wiped down with the rubbing alcohol/q-tip combo, place all of them into a bowl of warm water mixed with some dish soap or detergent – this will help remove any leftover dirt particles as well as add shine back into each bearing’s metal surfaces once they’re dry again. Let them soak for about 10 minutes before moving onto step 4!

4. After soaking in the soapy water solution for 10 minutes, take out each bearing one at a time and rinse off thoroughly under running tap water until no more suds appear – this should help get rid of any remaining dirt/grime residue stuck inside too!

Make sure not to leave behind any excess moisture when drying off; instead pat gently with either another rag/paper towel before moving onto step 5 below.

5. Finally , put each cleaned bearing back where it came from before beginning work on the next one – don’t forget – if using lubricant be sure to apply only after everything else has been done !

This way , you won’t have messy greasing up happening while trying to get details like tightening screws right . Now go enjoy those smooth rides knowing your skateboard is ready to roll !


Cleaning skateboard bearings is an important part of maintaining your board’s performance. Fortunately, it’s easy to do and doesn’t take much time. All you need is some bearing cleaner or degreaser, a soft cloth or paper towel, and a few tools like tweezers and needle-nose pliers for removing the shields from each bearing.

First, use the tweezers to remove any dirt from around the bearings then use the needle-nose pliers to remove the shields on each side of the bearings. Next, apply some bearing cleaner or degreaser onto a clean cloth or paper towel and gently wipe away any remaining dirt and grime from both sides of all your bearings.

Once they are completely dry, reassemble them by replacing their shields with your needle-nose pliers before putting them back into your skateboard wheels—and you’re done!

Cleaning skateboard bearings only takes a few minutes but can make a big difference in how well your board performs!